PRIMER PU-1000

Single-component, solvent based, polyurethane resin as a primer

PRIMER PU-1000 is a single component, low viscosity, high solids content polyurethane resin. It has been specifically designed to increase bonding and improve the surface leveling of the substrates prior to the application of the DESMOPOL or TECNOCOAT.

Download PDF data sheet . PRIMER PU-1000TDS. Technical Data sheet Download all documents . PRIMER PU-1000Downloads

Uses

Polyurethane resin to use in:

  • it is specially designed to increase the adherence and improve planimetry of the substrates where will be applied DESMOPOL or TECNOCOAT waterproofing liquid system membranes.
  • to apply in porous substrates such as concrete, mortar, or on plywood surfaces
  • highly recommended as a bonding material on waterproofing membranes and PU resins repairs and overlaps work.

NOTE: call our technical department about the application to other supports or situations

density at 23ºC 1,11 g/cm³
adhesion on concrete > 2 MPa
drying time at 23ºC ±60 minutes
dilution maximum: 5% DESMOSOLVENT 

GENERAL FEATURES

  • Single component polyurethane-based resin.
  • It needs a flat, clean, and dry surface, as hard as possible.
  • It can be applied on porous surfaces: concrete, cement,  and on plywood
  • It can be diluted in supports of low absorption.
  • Depending on the state of the surface to be treated, unevenness, or plane level, the yield can vary between 100~200 g/m², in one or several thin layers. (do not apply thick coats)
  • In applications on old, existing PUA and PU membranes or whatever with and smooth surface, the consumption will be between 50-100 g/m² (check "Repair and overlaps processes", in the Desmopol and Tecnocoat membranes' TDS)
  • It can be applied with a roller, brush or airless spray equipment
  • It can be applied on surfaces with a maximum surface humidity of 5%.
  • Do not apply to surfaces that are damp or exuding water coming from the interior of the substrate (water pressure due to phreatic level, condensations, leaks, etc.).
  • It can be applied in combination with mineral particles (silica sand) on very uneven surfaces.
  • Translucent

PACKAGING

Metal tins of 5 kg and 20 kg.

SHELF LIFE

12 months for each product at temperatures between 5° C and 35° C, provided it is stored in a dry place. Once the tin has been opened, the product must be used immediately.

APPLICATION METHOD

  • The surface must be clean and dry. If necessary, use pressure water to remove any oil or grease residue, efflorescence, or other contaminants, as well as loose cement laitance.
  • In some cases, it will be necessary to use mechanical processes to prepare the surface, as well as chemical means to clean metal surfaces.
  • Wait until the total evaporation of this cleaning water or check the support moisture.
  • Before applying, take into account the residual humidity from cleaning, that is, wait until its total evaporation or verify any humidity in the surface using a measuring device.
  • You can use DESMOSOLVENT(max.5 % dilution). Mix for 2 minutes, or until achieving a correct mixture
  • Apply one or more coats (depending on support conditions) of PRIMER PU-1000 until the desired thickness is obtained.
  • If the surface to be treated is very uneven, apply an initial coat of PRIMER PU-1000 mixed with mineral filings to level it.
  • Wait until completely dry before applying the desired waterproofing or concrete protection system.

HANDLING AND TRANSPORT

These safety recommendations for handling, are necessary for the implementation process as well as in the pre and post, on exposure to the loading machinery.

  • Respiratory Protection: When handling or spraying use an air-purifying respirator.
  • Skin protection: Use rubber gloves, remove immediately after contamination. Wear clean body-covering. Wash thoroughly with soap and water after work and before eating, drinking, or smoking.
  • Eye / Face: Wear safety goggles to prevent splashing and exposure to particles in the air.
  • Waste: Waste generation should be avoided or minimized. Incinerate under controlled conditions in accordance with local laws and national regulations.

Anyway, consult the material and safety data sheet of the product(MSDS) or contact our technical department.


PROPERTIES

PROPERTIES

RESULT

Density at 23 ºC   ISO 1675

1,11 g/cm³

Viscosity at 23 ºC    ISO 2555 ±120 cps

Solids content     ISO 1768

>80%

VOC(volatile organic compounds) 270 g/l

Adhesion to concrete

> 2 MPa

Drying time at 23 ºC

±60 minutes

Final dry time at 23 ºC

2~3 hours

Recoat range time at 23 ºC

3~24 hours

Environmental application range temperature

5~35 ºC

Max. Moisture on the support

5%

Dilution

±5% DESMOSOLVENT

 

The values in this table are approximate and can vary depending on the situation of the support or application methodology employed